Motorservice, Yanmar, Yanmar Service, Yanmar filtre
Drawing of a Yanmar 3GM30F

Engine Service

Changing the fuel filters looked easy on YouTube. Then the engine coughed, sighed and died. With diesel everywhere, fogged-up glasses and rising panic, I discovered what DIY engine service is really about.

Engine service

I had decided to service the engine myself. From now on, it would be me – not the mechanic – changing the filters, oil, coolant and impeller, and winterising the engine.

A fairly ambitious plan, considering that I still haven’t figured out how to open the bonnet of our car.

Changing the filters

I decided to start with the most urgent job: changing the filters. The rest could wait until later.

I had found a video on YouTube in which a man showed how to do it. His engine, like ours, was a Yanmar 3GM30F, and I had also looked over the mechanic’s shoulder a couple of times.

So how difficult could it really be?

I got the tools and spare parts out, put everything together in one place and carefully covered the engine compartment with newspapers and rags.

Two filters

There are two fuel filters on our boat: a primary filter and a secondary filter.

Changing them turned out to be surprisingly easy.

Both of them.

When I had finished, I started bleeding the fuel system.

Bleeding the system

I began by loosening the screw on top of the primary filter. At first, air came out, but then gravity did its job and the diesel began to flow. A mixture of air and diesel bubbled around the screw. Eventually, only diesel came out.

I tightened the screw and the diesel stopped flowing.

Primary filter bled.

Check.

On to the secondary filter. It sits above the diesel tank, which meant I had to operate the little manual priming lever on the fuel pump. But no matter how much I pumped, only air came out.

That hadn’t happened to the man in the YouTube video, and as far as I remembered, it hadn’t happened to the mechanic either.

Then I remembered Bertil telling me that the engine was self-bleeding.

Surely that meant the remaining air would disappear when I started the engine?

I turned the ignition key. When the red warning light came on and the alarm sounded, I pressed the starter button.

To my enormous relief, the engine started just as it normally did.

But my relief turned to panic and confusion when the engine gave a deep sigh and died.

I tried again.

Nothing happened.

Nothing at all.

…Damn.

The diagnosis was actually quite simple.

Air in the fuel system.

What now?

I considered calling the mechanic and telling him that the engine wouldn’t start.

But what was I supposed to say?

“Hi John. You know, the last time you were here, I watched you change the filters. And I thought, well, I can easily do that myself. So now I’ve changed them. Buuut… the engine won’t start. Any chance you could come over and help?”

I was going to have to sort this out myself.

I bled the primary filter again.

No problems there.

Then I started bleeding the secondary filter.

Still nothing but air.

I removed it, checked the O-ring and, with some difficulty, fitted it again.

And pumped and pumped and pumped.

Only when I squeezed myself in behind the engine, where I could put my full body weight behind each stroke of the pump, did diesel finally begin bubbling around the screw.

Eventually, only diesel came out.

Bleeding complete.

Check.

Full of confidence, I turned the ignition key and triumphantly pressed the starter button.

Still nothing.

…Damn.

Another screw

Then I remembered that a mechanic had once told me that it was also necessary to bleed the system at another screw further along the fuel line.

I found it.

It looked rather rusty.

Was this really the one?

I pulled up a manual on my iPhone, but I couldn’t read it because my glasses had fogged up from the sweat that had been pouring down my face for some time.

Eventually, I decided that it had to be the right screw.

I put the spanner on it.

Turned carefully.

The screw was really tight.

Was I doing the right thing?

Finally, it came loose.

…Phew. At least it didn’t snap.

Then I pumped and pumped again.

At last, diesel began bubbling around the screw, and shortly afterwards only diesel flowed out.

Once again, I bled the system at all three screws.

And then the miracle happens

Feeling slightly discouraged, I turned the ignition key one more time and pressed the starter button.

And then the miracle happened.

The engine started.

And this time it kept running.

I pushed the throttle forward. The revs rose smoothly. I let it run for a while, listening carefully.

Everything sounded exactly as it should.

I had changed the filters, filled the fuel system with air, brought the engine to a complete standstill – and somehow managed to get it running again.

What a feeling.

Perhaps servicing the engine myself wasn’t such a ridiculous idea after all.

Now I just have to figure out how to open the bonnet of the car.

Links

A little about engine servicing

Of course, I could also have called Lennart

Grovfilter
Finfilter
Tredje

 

Thank you for reading the story 

 

We love hearing from our readers.

A greeting, comment or question?

Go ahead

…everything is welcome

This website uses cookies. By continuing to use this site, you accept our use of cookies. 

Abonnér på vores fortællinger

10
0
Skriv din hilsen her ... x
()
x